POWERHOUSE CORNER GYM GS 9 IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 w
STEP 4 (See Diagram 4) A.) Attach the Front Press Base (#97) to the Right Base Frame (#46). Secure it with a 9 ¼” Front Press Axle (#60), two ∅ ¾”
STEP 5 (See Diagram 5) A.) Attach the Butterfly Support Frame (#18) to the front of Right Vertical Beam (#21). Attach the Butterfly Pulley Support (
STEP 6 (See Diagram 6) A.) Attach the Vertical Press Frame (#78) to the Rear Vertical Beam (#50). Secure it with a M10 x 4 7/8” Vertical Press Axl
CABLE LOOP DIAGRAM 12
STEP 7 (Upper Cable Loop & Diagram 7) A.) Attach the 108” Upper Cable (#93) to the front opening on the Upper Frame (#8). Attach a Pulley (#79)
DIAGRAM 7 14
STEP 8 (See Butterfly Cable Loop & Diagram 8) A.) Attach the 114” Butterfly Cable (#95) to the slot on the back of Left Butterfly (#20). Draw
DIAGRAM 8 16
STEP 9 (See Front Press Cable Loop & Diagram 9) A.) Attach the 224” Front Press Cable (#94) to the lower opening on the Leg Developer (#40).
FRONT PRESS CABLE LOOP DIAGRAM 18
TABLE OF CONTENTS BEFORE YOU BEGIN... 1 IMPORTANT SAFETY NOT
DIAGRAM 9 19
STEP 10 (See Leg Press Cable Loop & Diagram 10) A.) Attach one end of the 97” Leg Press Cable (#96) to the open slot on the back of the Leg Pr
LEG PRESS CABLE LOOP DIAGRAM 21
DIAGRAM 10 22
STEP 11 (See Diagram 11) A.) Place a Seat Pad (#29) onto the Left Seat Support (#92). Secure it with two M8 x 1 3/8” Allen Bolts (#106) and ∅ 5/8”
STEP 12 (See Diagram 12) A.) Place a Seat Pad (#29) onto the Right Seat Support (#49). Secure it with two M8 x 2 1/8” Allen Bolts (#25) and ∅ 5/8”
STEP 13 (See Diagram 13) A.) Securely tighten all the nuts and bolts previously installed. B.) Before putting the Weight Plates on, now move the m
27
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Lat Bar Grip 2 2 Lat Bar 1 3 Chain 4 4 C-clip 6 5 M10 Aircraft Nut 52 6 ∅ ¾” Washer 88 7 Bracket 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a p
WEIGHT RESISTANCE CHART WEIGHT PLATE Station 1 2 3 4 5 6 7 8 9 Low Pulley 35 45 55 65 75 85 95 105 115 Lat Pull 20 30 40 50 60 70 80 90 100
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal
HARDWARE PACK 3
HARDWARE PACK 4
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or peop
STEP 2 (See Diagram 2) A.) Attach the Right Vertical Beam (#21) to the Right Base Frame (#46). Secure it with two M10 x 2 ½” Carriage Bolts (#17)
STEP 3 (See Diagram 3) A.) Slide two ∅ 2 ½” Rubber Bumpers (#58) onto two Chromed Guide Rods (#22). Insert the two Guide Rods into the holes on t
DIAGRAM 3 8
Comments to this Manuals