Impex MWB-4360 User Manual

NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instructi

STEP 3 (See Diagram 3) A.) Attach the Rear Vertical Beam (#6) to the top of the Cross Brace (#2). Attach the Weight Glide Base (#8) to the Cross Br

STEP 4 (See Diagram 4) A.) Attach the Weight Glide Post (#7) onto the Weight Glide Base (#8). Secure it with four M10 x 1” Carriage Bolts (#74), Ø ¾

STEP 5 (See Diagram 5) A. Place the Left Upper Frame (#94) onto the Front Top Beam (#15). Secure it with two M10 x 3 1/8” Carriage Bolts (#77), on

STEP 6 (See Diagram 6) A.) Securely tighten all Nuts and Bolts previously installed. B.) Attach the Butterfly Base (#12) to the front of Rear Vertic

CABLE LOOP DIAGRAM 13

STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach one end of 87” Butterfly Cable (#42) to the clip on Right Butterfly (#11). Draw the Cable

STEP 8 (See Diagram 8 & Cable Loop Diagram) A.) Un-install the M10 x 1 1/8” Allen Bolt (#104) and M10 Aircraft Nut (#86) on the U-shaped Conn

16

STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach one end of the 138” Sliding Weight Post Cable (#102) to the open bracket on the Sliding

DIAGRAM 9 18

TABLE OF CONTENTS BEFORE YOU BEGIN...……………. 1 IMPORTANT SAFETY NOTICES...

STEP 10 (See Diagram 10) A.) Attach the 59” Lower Cable (#40) to a Pulley (#57). Attach the Pulley to the lower opening on the Rear Vertical Beam (#6

STEP 11 (See Diagram 11) A.) NOTE: Help of another person is strongly recommended for this step. Place the Lifting Sleeve (#27) in between the two S

EXPLODED DIAGRAM 21

PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Base Frame 2 55 Sliding Sleeve 8 2 Cross Brace 1 56 Lock Ring 2 3 Front Vertica

MULTI-PURPOSE BENCH HARDWARE PACK 23

MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly

STEP 2 (See Diagram 2) A.) Attach four Bushings (#27) to a Seat Support Frame (#6). B.) Attach a Backrest Support (#7) to the rear of the Seat Sup

STEP 3 (See Diagram 3) A.) Place the Backrest Board (#14) onto the Backrest Supports (#7). Secure it with four M8 x 2” Allen Bolts (#40) and ∅ 5/8

STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#5) to the open bracket on the Main Frame (#1). Secure it with an Axle (#17), two M10 x ¾”

STEP 5 (See Diagram 5) A.) Attach the Arm Curl Pad (#15) to the Arm Curl Stand (#4). Secure it with two M8 x 5/8” Allen Bolts (#41) and two ∅ 5/8”

IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a p

29

MULTI-PURPOSE BENCH PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Main Frame 1 2 Front Stabilizer 1 3 Rear Stabilizer 1 4 Arm Curl Stand 1 5 Leg Develo

MWB-4360 WEIGHT RESISTANCE CHART Station Ratio Example Low Pulley 200% 10 lb. plate creates 20 lb. resistance Lat Pull 50% 10 lb. plate create

IMPEX® INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX®") warrants this product to be free from defects in workmanship and material, under normal

WARNING LABEL PLACEMENT The warning labels shown here have been placed on the Rear Base, Rear Stabilizer, and Upper Frame. If the labels are missi

SMITH MACHINE HARDWARE PACK 4

SMITH MACHINE HARDWARE PACK 5

SMITH MACHINE ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recomme

STEP 2 (See Diagram 2) A.) Attach a Front Vertical Frame (#3) to the Right Base Frame (#1). Secure it with two M10 x 3” Carriage Bolts (#76), on

DIAGRAM 2 8