NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Pack Assembly Instruction Par
STEP 3 (See Diagram 3) A.) Attach the Front Vertical Beam (#3) to the Main Base Frame (#2). Secure it with one M10 x 2 ¾” Allen Bolt (#104), two Ø
STEP 4 (See Diagram 4) A.) Attach the Seat Support (#11) to the Front Vertical Beam (#3) and Main Base Frame (#2). Secure it to the Front Vertical
STEP 5 (See Diagram 5) A.) Place the Seat (#61) onto the Seat Incline Adjustment (#13). Secure it with two M10 x 1 ¾” Allen Bolts (#101) and Ø ¾” Wa
STEP6 (See Diagram 6) A.) Slide the Sliding Pulley Frame (#21) onto the Sliding Pulley Vertical Beam (#9) from the bottom. Use a Lock Knob (#71) to
STEP 7 (See Diagram 7) A.) Attach a Pulley to the front opening on the Upper Frame (#5). Secure it with one M10 x 2 ½” Allen Bolt (#103), two Ø ¾”
STEP 8 (See Diagram 8) A.) Insert the Right Butterfly Arm (#6) into the pivot on the Front Vertical Beam (#3). Secure it with one M10 x ¾” Allen
STEP 9 (See Diagram 9) A.) Attach the Bench Press Base (#32) to the pivot on the Upper Frame (#5). Align the holes and insert a 8” Bench Press Axl
STEP 10 (See Diagram 10) A.) Attach the Backrest Adjustment Frame (#10) to the Front Vertical Beam (#3). Secure the bottom of the Frame to the Fro
STEP 11 (See Diagram 11) A.) Align two Ø 2 ½” x 1” Rubber Bumpers (#76) onto the holes on the Main Base Frame (#2). Insert two Guide Rods (#15) thr
STEP 12 (See Diagram 12) A.) Attach two Pulleys to each Angled Double Floating Pulley Bracket (#26). Secure each Pulley with one M10 x 1 ¾” Alle
TABLE OF CONTENTS BEFORE YOU BEGIN... 1 IMPORTANT SAFETY NOTIC
STEP 13 Upper Cable Looping (See Diagram 13) A.) Slide a Ball Stopper (#70) onto the 161” Upper Cable (#52). Slide and Pull the Cable Strap Brac
DIAGRAM 13 20
STEP 14 High-Low Station Cable Looping (See Diagram 14) A.) Slide a Ball Stopper (#70) onto the 262” High-Low Cable (#53). Slide and Pull the Ca
DIAGRAM 14 22
STEP 15 Lower & AB Cable Looping (See Diagram 15) A.) Insert the 265” Lower Cable underneath the Pulley on the Leg Developer (#12). B.) Draw
DIAGRAM 15 24
STEP 16 Butterfly Cable Looping (See Diagram 16) A.) Attach one end of the 99” Butterfly Cable (#55) to the bottom of the Right Butterfly (#6). Secu
STEP 17 Tension Cable looping (See Diagram 17) A.) Thread the bolt on the 161” Tension Cable (#56) into the Single Floating Pulley Bracket (#23) pre
STEP 18 (See Diagram 18) A.) Attach two Weight Plate Covers (#16) to the Top Socket Assembly (#20) and Main Base Frame (#2). Secure each Weight Pl
28
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a p
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Bench Press Arm 1 2 Main Base Frame 1 3 Front Vertical Beam 1 4 Rear Vertical Beam 1 5 Upper Frame
111 M6 x ¼” Socket Set Screw 1 112 M6 x 3/8” Socket Set Screw 2 113 M10 x ½” Socket Set Screw 4 114 M10 x
IGS-16 WEIGHT RESISTANCE CHART * Numbers are approximate. Actual weights may vary. * Values for Butterfly are for each arm. 31 WEIGHT PLATE
IRON GRIP SPORT By IMPEX FITNESS PRODUCTS LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmans
HARDWARE PACK 3
HARDWARE PACK 4
HARDWARE PACK 5
HARDWARE PACK 6
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machin
STEP 2 (See Diagram 2) A.) Attach the Main Base Frame (#2) and the Rear Base (#18) to the bottom of the Rear Vertical Beam (#4). Align the holes
Comments to this Manuals