NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Pack Assembly Instruction Pa
DIAGRAM 2 9
STEP 3 (See Diagram 3) A.) Slide 14 Weight Plates (#42) onto the Guide Rods (#11). Make sure the deep grooves on the Weight Plates all face the back
STEP 4 (See Diagram 4) A.) Place the Upper Frame (#1) onto the Vertical Frame (#4). B.) Attach the brackets on the Upper Frame to the two Guide R
DIAGRAM 4 12
STEP 5 (See Diagram 5) A.) Attach the Front Press Base (#8) to the Upper Frame (#1). Secure it with one 8 ½” Front Press Axle (#19), two Ø 1” Large
DIAGRAM 5 14
STEP 6 (See Diagram 6) A.) Attach the Left Dip Support (#28) into Right Dip Support (#27) behind the Power Station Vertical Frame (#26). B.) Attach t
DIAGRAM 6 16
STEP 7 (See Diagram 7) A.) Attach one Swivel Pulley Bracket (#17) to the open bracket on the back of Vertical Frame (#4). Secure it with one M10 x 2 ½
STEP 8 (See Diagram 8) A.) Attach the Power Station Arm Pads (#35) to the Right & Left Dip Support (#27 & #28). Secure each Arm Pad with two M
TABLE OF CONTENTS BEFORE YOU BEGIN...……….. 1 IMPORTANT SAFETY N
STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach the 127 ½” Upper Cable (#56) to the front open bracket under the Upper Frame (#1). B.)
DIAGRAM 9 20
STEP 10 (See Diagram 10 & Cable Loop Diagram) A.) Hook one end of the 98” Butterfly Cable (#57) to Right Butterfly (#10). B.) Draw the Cable to
STEP 11 (See Diagram 11 & Cable Loop Diagram) A.) Attach the 159” Lower Cable (#58) to the opening bracket on Leg Developer (#7). B.) Attac
STEP 12 (See Diagram 12) A.) Connect Lat Bar (#14) to the Upper Cable (#56) with two Hooks (#63) and one 15-link Chain (#55) when doing Lat Pull exerc
STEP 13 (See Diagram 13) A.) Do not tighten the Bolts until instructed to do so. B.) Attach one Weight Stack Bracket (#100) to the bracket on Upper Fr
Set up the Lock Combination A.) The combination is pre-set to 0-0-0 by the factory. B.) Turn the dials to 0-0-0 and aligned to the Combination Set Up
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Upper Frame 1 51 Ø 1” x Ø ½” Bushing 2 2 Middle Stabilizer 1 52 Ø 1” x 5/8” Pulley Bushing 4
MWM1860 WEIGHT RESISTANCE CHART Weight Plate Leg Developer Front Press Butterfly Lat Pull Low Pulley 1 30 31 15
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piec
IMPEX® INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX®") warrants this product to be free from defects in workmanship and material, under norma
WARNING LABEL PLACEMENT The warning labels shown here have been placed on the Middle Stabilizer and Upper Frame. If the labels are missing or ille
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 4
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 5
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 6
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that th
STEP 2 (See Diagram 2) A.) Insert the two Guide Rods (#11) into the holes on the Middle Stabilizer (#2). Secure each Guide Rod with one M10 x
Comments to this Manuals